How can i disassemble my iphone 4

This will turn the display off when you bring the phone up to your ear thus preventing any touch interaction while it's pressed up against ear.

As always, we provide each device with a fitting final layout shot that it so greatly deserves. We would like to thank you for joining us tonight during this monumental endeavor. We also created a set of iPhone 4 repair guides for all major components inside the device. They will definitely help you fix your iPhone 4 should something happen to it! The iPhone 4 is held together primarily with [lots of] screws, sans tabs, and limited adhesive. Apple is using Pentalobe screws to secure the rear panel and keep people out.

The LCD and glass are fused together, making repairing a cracked front panel more costly. During disassembly, your finger oils interfere with the iPhone 4's RF grounding contact points, so we recommend you wear gloves while performing any repairs.

Badges: Obviously creating antennas out of the frame pieces didn't work well for them The "dual-band" enhancement is worthless - cellular got kicked off the MHz spectrum. Alex - July 5. Fix Your Stuff Community Store. Tools Featured in this Teardown. P2 Pentalobe Screwdriver iPhone The iPhone 4 originally shipped with Phillips 00 screws on its outer case, but a hardware update later changed them to Pentalobe screws. Introduction We stripped the iPhone 4 down to its basic components.

Step 1 iPhone 4 Teardown. Add a comment. Add Comment Cancel. Step 2. Step 3. Step 4. Tool used on this step:. Step 5. Step 6. Step 7. Step 8. Step 9. Step One comment. Author with 19 other contributors. Walter Galan , Reputation 1, Guides authored. What happens if you strip a screw.. How do you go about getting it out? Simply trace around the phone on a piece of paper for a schematic on the screws later. This is the primary way I organized everything. I used two ways of holding the screws.

Cut a slit in the paper with an X-Acto and slipping in the screw exactly where the screw would be on the real phone. Tap small pieces of tape to the location it would be on the phone 3.

Llastly, put the screws on the frame where all of them will be easily differentiable so I just put them on a piece of duct tape for easy storage. With a simple paper clip, push in on the Sim Card slot hole and the holder should pop up.

A bit of pressure is needed. Easy as pie! Lay your phone with its back facing you. Simply unscrew the small screws at the bottom of the phone with your Philips head screw driver. Push the front cover upward, it should come loose.

Place the screws in an organized place such as the photo shown below. Remove a screw on the iPhone, look at photo for reference. Gently pry this up from the side opposite to the battery and make sure to keep the small black piece that comes out with it, organize these in your notebook below.

The battery takes a lot of force! This should help you out but it still takes a bit of time to loosen it from its adhesive. Do not use a screw driver to take this out, it may short the battery, a simple guitar pick will do the trick. For this process you will need to base your actions on the images below. Make sure to organize the screws and make small sketches of reference points, mine was the camera.

Remember that when taking out the plate after all of the screws are removed there are two hooks that you need to take into count when your are wiggling it out.

For this step you will be in close contact with the mother board so be extremely careful: 1. Simply remove two screws which are indicated below and the plate should come off, no hooks.

Remember set these aside and draw where they were. Here is the difficult part, under the shield there is a connector, simply pry it up from the top side of your phone. These steps are as usual and easy ones: 1. Simply unscrew the screws below and set aside the entire motor.

Remember sketch this out and organize! These steps are possibly the more delicate moves: 1. Remove the camera after this step no hooks or screws. For this step you will have to go back to the small connector under the shield on step two. Gently peel away the long ribbon cable. It is vital that you do this carefully because this can easily rip. After it is peeled away and laying gingerly at its side remove the two screws indicated below.

Then after removing each screw use a flat head screw driver or a safety pry tool to disconnect the speaker connector, this is shown on the 6th picture. Organize each part as you have been doing. This step is directly handling the mother board of the iPhone so i can not stress this enough, be careful. The photos below will show you the difference. This is probably the most time consuming step in the entire process for this you will need to remove 10 screws, 6 larger ones with washers on the sides classified as A screws, and 4 smaller ones in the corners classified as B screws.

Follow the photo below for thier exact positions. Organize as shown below on a piece of tape. Take some time to slowly guide a guitar pick around the edges of the metal frame and the plastic boarder, it really does not matter if you put some force, even if your not getting any where with a pick use a small knife and make a small entry for your pick and glide it around a few times to take off the adhesive.

Then here is your moment of glory! Before you install your screen. Make sure you have taken off the clear adhesive on both ends of the phone. Make sure that clear camera adjustment is still on phone. Make sure the speaker grill is set on your new display!. Make sure both ribbon cables are standing upright and are parallel to each other. Installing screen, i could not take a photo of this because i was putting it together two handed.

Simply guide the new ribbon cables through the hole that you took the old display out of, you sort of have to play around till the cable and a small metal box fit snugly inside the enclosure.

Im not going to go into detail but just follow each step backwards. He joined 9to5Mac to share even more tech news around the world. January Despite the price, these are great gifts to give to yourself or a friend who loves Apple.

Be sure to check out our homepage for all the latest news, and follow 9to5Mac on Twitter , Facebook , and LinkedIn to stay in the loop.